OmronE5.h File Reference

Go to the source code of this file.

Macros
#define	OR_BIT(A)   (A >> 1)
#define	OR_E5_CMD(CMD, VALUE)   (CMD | VALUE)
#define	OR_E5_STATUS_BIT(H, L, B)   (B <= 16 ? (L & (1 << 8)) : (OR_WORD(H) & (1 << (OR_BIT(B)))))
#define	OR_E_MSG_INVALID_ADDRESS   "Invalid Variable Address"
#define	OR_E_MSG_INVALID_RANGE   "Invalid Variable Range"
#define	OR_E_MSG_OPERATION_ERROR   "OPERATION ERROR"
#define	OR_WORD(A)   (A << 4)

Enumerations
enum	OR_E5_CMD { OR_E5_STOP = OR_E5_CMD(OR_E5_CMD_ADDRESS::OR_E5_CMD_STOP_RUN, 1), OR_E5_RUN = OR_E5_CMD(OR_E5_CMD_ADDRESS::OR_E5_CMD_STOP_RUN, 0), OR_E5_AT_CANCEL = OR_E5_CMD(OR_E5_CMD_ADDRESS::OR_E5_CMD_AT, 0), OR_E5_AT_EXCECUTE = OR_E5_CMD(OR_E5_CMD_ADDRESS::OR_E5_CMD_AT, 1) }
enum	OR_E5_CMD_ADDRESS { OR_E5_CMD_STOP_RUN = 0x100, OR_E5_CMD_COM_WRITE = 0x000, OR_E5_CMD_AT = 0x200 }
enum	OR_E5_ERROR { VARIABLE_ADDRESS_ERROR = 0x2, VARIABLE_RANGE_ERROR = 0x3, VARIABLE_OPERATION_ERROR = 0x4 }
enum	OR_E5_RESPONSE_CODE { OR_READ_ERROR = 0x83, OR_RESPONSE_OK = 0x10, OR_OPERATION_ERROR = 0x90, OR_COMMAND_ERROR = 0x86 }
enum	OR_E5_STATUS_1 {   OR_E5_S1_Heater_OverCurrent = 0, OR_E5_S1_Heater_CurrentHold = 1, OR_E5_S1_AD_ConverterError = 2, OR_E5_S1_HS_Alarm = 3,   OR_E5_S1_RSP_InputError = 4, OR_E5_S1_InputError = 6, OR_E5_S1_PotentiometerInputError = 7, OR_E5_S1_Control_OutputOpenOutput = 8,   OR_E5_S1_Control_OutputCloseOutput = 9, OR_E5_S1_HBAlarmCT1 = 10, OR_E5_S1_HBAlarmCT2 = 11, OR_E5_S1_Alarm1 = 12,   OR_E5_S1_Alarm2 = 13, OR_E5_S1_Alarm3 = 14, OR_E5_S1_ProgramEndOutput = 15, OR_E5_S1_EventInput1 = 16,   OR_E5_S1_EventInput2 = 17, OR_E5_S1_EventInput3 = 18, OR_E5_S1_EventInput4 = 19, OR_E5_S1_WriteMode = 20,   OR_E5_S1_NonVolatileMemory = 21, OR_E5_S1_SetupArea = 22, OR_E5_S1_ATExcecute = 23, OR_E5_S1_RunStop = 24,   OR_E5_S1_ComWrite = 25, OR_E5_S1_AutoManualSwitch = 26, OR_E5_S1_ProgramStart = 27, OR_E5_S1_HeaterOverCurrentCT2 = 28,   OR_E5_S1_HeaterCurrentHoldCT2 = 29, OR_E5_S1_HSAlarmCT2 = 31 }
enum	OR_E5_STATUS_2 {   OR_E5_S2_WorkBit1 = 0, OR_E5_S2_WorkBit2 = 1, OR_E5_S2_WorkBit3 = 2, OR_E5_S2_WorkBit4 = 3,   OR_E5_S2_WorkBit5 = 4, OR_E5_S2_WorkBit6 = 5, OR_E5_S2_WorkBit7 = 6, OR_E5_S2_WorkBit8 = 7,   OR_E5_S2_EventInput5 = 16, OR_E5_S2_EventInput6 = 17, OR_E5_S2_Inverse = 20, OR_E5_S2_SPRamp = 21,   OR_E5_S2_SPMode = 27, OR_E5_S2_Alarm4 = 28 }
enum	OR_E5_SWR {   OR_E5_SWR_PV = 0x2000, OR_E5_SWR_STATUS = 0x2001, OR_E5_SWR_ISP = 0x2002, OR_E5_SWR_HeaterCurrentValue1_Monitor = 0x2003,   OR_E5_SWR_MVMonitorHeating = 0x2004, OR_E5_SWR_MVMonitorCooling = 0x2005, OR_E5_SWR_SP_LIMIT = 0x2103, OR_E5_SWR_ALARM_1 = 0x2104,   OR_E5_SWR_ALARM_1_UL = 0x2105, OR_E5_SWR_ALARM_1_LL = 0x2106, OR_E5_SWR_ALARM_2 = 0x2107, OR_E5_SWR_ALARM_2_UL = 0x2108,   OR_E5_SWR_ALARM_2_LL = 0x2109, OR_E5_SWR_PV2 = 0x2402, OR_E5_SWR_ISP2 = 0x2403, OR_E5_SWR_MSMON = 0x2404,   OR_E5_SWR_STATUSEX = 0x2406, OR_E5_SWR_STATUSEXL = 0x2407, OR_E5_SWR_STATUSEXR = 0x2408, OR_E5_SWR_DECMON = 0x2410,   OR_E5_SWR_SP = 0x2601, OR_E5_SWR_SP_EX_MON = 0x2602, OR_E5_SWR_HeaterCurrentValue1_Monitor2 = 0x2604, OR_E5_SWR_VALVE_OPENING_MON = 0x2607,   OR_E5_SWR_PRO_BAND = 0x2701, OR_E5_SWR_IT_COOLING = 0x2702, OR_E5_SWR_D_COOLING = 0x2703, OR_E5_SWR_DEADBAND = 0x2704,   OR_E5_SWR_MANUAL_RESET_VALUE = 0x2705, OR_E5_SWR_HYSTERESIS = 0x2706, OR_E5_SWR_HYSTERESIS_COOLING = 0x2707, OR_E5_SWR_CONTROL_PERIOD_HEATING = 0x2708,   OR_E5_SWR_CONTROL_PERIOD_COOLING = 0x2709, OR_E5_SWR_POSITION_PROPORTIONAL_DEAD_BAND = 0x270A, OR_E5_SWR_OPEN_CLOSE_HYSTERESIS = 0x270B, OR_E5_SWR_SP_RAMP_UNIT = 0x270C,   OR_E5_SWR_SP_RAMP_SET_VALUE = 0x270D, OR_E5_SWR_SP_FALL_VALUE = 0x270E, OR_E5_SWR_MV_PV_ERROR = 0x2711, OR_E5_SWR_CHANGE_RATE_LIMIT = 0x2713,   OR_E5_SWR_PV_INPUT_SLOPE_COEFFICIENT = 0x2718, OR_E5_SWR_HEATER_BURNOUT_DETECTION_1 = 0x271B, OR_E5_SWR_LEAKAGE_CURRENT_MONITOR_1 = 0x271C, OR_E5_SWR_HS_ALARM_1 = 0x271D,   OR_E5_SWR_PROCESS_VALUE_INPUT_SHIFT = 0x2723, OR_E5_SWR_HEATER_BURNOUT_DETECTION_2 = 0x2725, OR_E5_SWR_LEAKAGE_CURRENT_MONITOR_2 = 0x2726, OR_E5_SWR_HS_ALARM_2 = 0x2727,   OR_E5_SWR_SOAK_REMAIN = 0x2728, OR_E5_SWR_SOAK_TIME = 0x2729, OR_E5_SWR_WAIT_BAND = 0x272A, OR_E5_SWR_REMOTE_SP_SHIFT = 0x272B,   OR_E5_SWR_REMOTE_SP_SLOPE_COEFFICIENT = 0x272C, OR_E5_SWR_DIGITAL_FILTER = 0x2800 }

Macro Definition Documentation

OR_BIT

#define OR_BIT

(

A

)

(A >> 1)

Definition at line 6 of file OmronE5.h.

OR_E5_CMD

#define OR_E5_CMD	(		CMD,
			VALUE
	)		(CMD | VALUE)

Definition at line 10 of file OmronE5.h.

OR_E5_STATUS_BIT

#define OR_E5_STATUS_BIT	(		H,
			L,
			B
	)		(B <= 16 ? (L & (1 << 8)) : (OR_WORD(H) & (1 << (OR_BIT(B)))))

Definition at line 9 of file OmronE5.h.

OR_E_MSG_INVALID_ADDRESS

#define OR_E_MSG_INVALID_ADDRESS   "Invalid Variable Address"

Definition at line 356 of file OmronE5.h.

OR_E_MSG_INVALID_RANGE

#define OR_E_MSG_INVALID_RANGE   "Invalid Variable Range"

Definition at line 357 of file OmronE5.h.

OR_E_MSG_OPERATION_ERROR

#define OR_E_MSG_OPERATION_ERROR   "OPERATION ERROR"

Definition at line 358 of file OmronE5.h.

OR_WORD

#define OR_WORD

(

A

)

(A << 4)

Definition at line 7 of file OmronE5.h.

Enumeration Type Documentation

OR_E5_CMD

enum OR_E5_CMD

Enumerator
OR_E5_STOP
OR_E5_RUN
OR_E5_AT_CANCEL
OR_E5_AT_EXCECUTE

Definition at line 332 of file OmronE5.h.

{
    OR_E5_STOP = OR_E5_CMD(OR_E5_CMD_ADDRESS::OR_E5_CMD_STOP_RUN, 1),
    OR_E5_RUN = OR_E5_CMD(OR_E5_CMD_ADDRESS::OR_E5_CMD_STOP_RUN, 0),
    OR_E5_AT_CANCEL = OR_E5_CMD(OR_E5_CMD_ADDRESS::OR_E5_CMD_AT, 0),
    OR_E5_AT_EXCECUTE = OR_E5_CMD(OR_E5_CMD_ADDRESS::OR_E5_CMD_AT, 1)
};

OR_E5_CMD_ADDRESS

enum OR_E5_CMD_ADDRESS

Enumerator
OR_E5_CMD_STOP_RUN
OR_E5_CMD_COM_WRITE
OR_E5_CMD_AT

Definition at line 324 of file OmronE5.h.

{
    OR_E5_CMD_STOP_RUN = 0x100,
    OR_E5_CMD_COM_WRITE = 0x000,
    // Auto-Tune
    OR_E5_CMD_AT = 0x200
};

OR_E5_ERROR

enum OR_E5_ERROR

Enumerator
VARIABLE_ADDRESS_ERROR
VARIABLE_RANGE_ERROR
VARIABLE_OPERATION_ERROR

Definition at line 341 of file OmronE5.h.

{
    VARIABLE_ADDRESS_ERROR = 0x2,
    VARIABLE_RANGE_ERROR = 0x3,
    VARIABLE_OPERATION_ERROR = 0x4
};

OR_E5_RESPONSE_CODE

enum OR_E5_RESPONSE_CODE

Enumerator
OR_READ_ERROR
OR_RESPONSE_OK
OR_OPERATION_ERROR
OR_COMMAND_ERROR

Definition at line 348 of file OmronE5.h.

{
    OR_READ_ERROR = 0x83,
    OR_RESPONSE_OK = 0x10,
    OR_OPERATION_ERROR = 0x90,
    OR_COMMAND_ERROR = 0x86
};

OR_E5_STATUS_1

enum OR_E5_STATUS_1

Enumerator
OR_E5_S1_Heater_OverCurrent
OR_E5_S1_Heater_CurrentHold
OR_E5_S1_AD_ConverterError
OR_E5_S1_HS_Alarm
OR_E5_S1_RSP_InputError
OR_E5_S1_InputError
OR_E5_S1_PotentiometerInputError
OR_E5_S1_Control_OutputOpenOutput
OR_E5_S1_Control_OutputCloseOutput
OR_E5_S1_HBAlarmCT1
OR_E5_S1_HBAlarmCT2
OR_E5_S1_Alarm1
OR_E5_S1_Alarm2
OR_E5_S1_Alarm3
OR_E5_S1_ProgramEndOutput
OR_E5_S1_EventInput1
OR_E5_S1_EventInput2
OR_E5_S1_EventInput3
OR_E5_S1_EventInput4
OR_E5_S1_WriteMode
OR_E5_S1_NonVolatileMemory
OR_E5_S1_SetupArea
OR_E5_S1_ATExcecute
OR_E5_S1_RunStop
OR_E5_S1_ComWrite
OR_E5_S1_AutoManualSwitch
OR_E5_S1_ProgramStart
OR_E5_S1_HeaterOverCurrentCT2
OR_E5_S1_HeaterCurrentHoldCT2
OR_E5_S1_HSAlarmCT2

Definition at line 13 of file OmronE5.h.

{
    // Lower Word
 
    OR_E5_S1_Heater_OverCurrent = 0,
    OR_E5_S1_Heater_CurrentHold = 1,
    OR_E5_S1_AD_ConverterError = 2,
    OR_E5_S1_HS_Alarm = 3,
    OR_E5_S1_RSP_InputError = 4,
    OR_E5_S1_InputError = 6,
    OR_E5_S1_PotentiometerInputError = 7,
    OR_E5_S1_Control_OutputOpenOutput = 8,
    OR_E5_S1_Control_OutputCloseOutput = 9,
    OR_E5_S1_HBAlarmCT1 = 10,
    OR_E5_S1_HBAlarmCT2 = 11,
    OR_E5_S1_Alarm1 = 12,
    OR_E5_S1_Alarm2 = 13,
    OR_E5_S1_Alarm3 = 14,
    OR_E5_S1_ProgramEndOutput = 15,
 
    // Upper Word
 
    OR_E5_S1_EventInput1 = 16,
    OR_E5_S1_EventInput2 = 17,
    OR_E5_S1_EventInput3 = 18,
    OR_E5_S1_EventInput4 = 19,
    OR_E5_S1_WriteMode = 20,
    OR_E5_S1_NonVolatileMemory = 21,
    OR_E5_S1_SetupArea = 22,
    OR_E5_S1_ATExcecute = 23,
    OR_E5_S1_RunStop = 24,
    OR_E5_S1_ComWrite = 25,
    OR_E5_S1_AutoManualSwitch = 26,
    OR_E5_S1_ProgramStart = 27,
    OR_E5_S1_HeaterOverCurrentCT2 = 28,
    OR_E5_S1_HeaterCurrentHoldCT2 = 29,
    OR_E5_S1_HSAlarmCT2 = 31
};

OR_E5_STATUS_2

enum OR_E5_STATUS_2

Enumerator
OR_E5_S2_WorkBit1
OR_E5_S2_WorkBit2
OR_E5_S2_WorkBit3
OR_E5_S2_WorkBit4
OR_E5_S2_WorkBit5
OR_E5_S2_WorkBit6
OR_E5_S2_WorkBit7
OR_E5_S2_WorkBit8
OR_E5_S2_EventInput5
OR_E5_S2_EventInput6
OR_E5_S2_Inverse
OR_E5_S2_SPRamp
OR_E5_S2_SPMode
OR_E5_S2_Alarm4

Definition at line 54 of file OmronE5.h.

{
    // Lower Word
 
    OR_E5_S2_WorkBit1 = 0,
    OR_E5_S2_WorkBit2 = 1,
    OR_E5_S2_WorkBit3 = 2,
    OR_E5_S2_WorkBit4 = 3,
    OR_E5_S2_WorkBit5 = 4,
    OR_E5_S2_WorkBit6 = 5,
    OR_E5_S2_WorkBit7 = 6,
    OR_E5_S2_WorkBit8 = 7,
 
    // Upper Word
 
    OR_E5_S2_EventInput5 = 16,
    OR_E5_S2_EventInput6 = 17,
    OR_E5_S2_Inverse = 20,
    OR_E5_S2_SPRamp = 21,
    OR_E5_S2_SPMode = 27,
    OR_E5_S2_Alarm4 = 28
};

OR_E5_SWR

enum OR_E5_SWR

Enumerator
OR_E5_SWR_PV
OR_E5_SWR_STATUS
OR_E5_SWR_ISP
OR_E5_SWR_HeaterCurrentValue1_Monitor
OR_E5_SWR_MVMonitorHeating
OR_E5_SWR_MVMonitorCooling
OR_E5_SWR_SP_LIMIT
OR_E5_SWR_ALARM_1
OR_E5_SWR_ALARM_1_UL
OR_E5_SWR_ALARM_1_LL
OR_E5_SWR_ALARM_2
OR_E5_SWR_ALARM_2_UL
OR_E5_SWR_ALARM_2_LL
OR_E5_SWR_PV2
OR_E5_SWR_ISP2
OR_E5_SWR_MSMON
OR_E5_SWR_STATUSEX
OR_E5_SWR_STATUSEXL
OR_E5_SWR_STATUSEXR
OR_E5_SWR_DECMON
OR_E5_SWR_SP
OR_E5_SWR_SP_EX_MON
OR_E5_SWR_HeaterCurrentValue1_Monitor2
OR_E5_SWR_VALVE_OPENING_MON
OR_E5_SWR_PRO_BAND
OR_E5_SWR_IT_COOLING
OR_E5_SWR_D_COOLING
OR_E5_SWR_DEADBAND
OR_E5_SWR_MANUAL_RESET_VALUE
OR_E5_SWR_HYSTERESIS
OR_E5_SWR_HYSTERESIS_COOLING
OR_E5_SWR_CONTROL_PERIOD_HEATING
OR_E5_SWR_CONTROL_PERIOD_COOLING
OR_E5_SWR_POSITION_PROPORTIONAL_DEAD_BAND
OR_E5_SWR_OPEN_CLOSE_HYSTERESIS
OR_E5_SWR_SP_RAMP_UNIT
OR_E5_SWR_SP_RAMP_SET_VALUE
OR_E5_SWR_SP_FALL_VALUE
OR_E5_SWR_MV_PV_ERROR
OR_E5_SWR_CHANGE_RATE_LIMIT
OR_E5_SWR_PV_INPUT_SLOPE_COEFFICIENT
OR_E5_SWR_HEATER_BURNOUT_DETECTION_1
OR_E5_SWR_LEAKAGE_CURRENT_MONITOR_1
OR_E5_SWR_HS_ALARM_1
OR_E5_SWR_PROCESS_VALUE_INPUT_SHIFT
OR_E5_SWR_HEATER_BURNOUT_DETECTION_2
OR_E5_SWR_LEAKAGE_CURRENT_MONITOR_2
OR_E5_SWR_HS_ALARM_2
OR_E5_SWR_SOAK_REMAIN
OR_E5_SWR_SOAK_TIME
OR_E5_SWR_WAIT_BAND
OR_E5_SWR_REMOTE_SP_SHIFT
OR_E5_SWR_REMOTE_SP_SLOPE_COEFFICIENT
OR_E5_SWR_DIGITAL_FILTER

Definition at line 80 of file OmronE5.h.

{
    //Temperature: Use the specified range for each sensor.
    // Analog: Scaling lower limit − 5% FS to Scaling upper limit + 5% FS
    OR_E5_SWR_PV = 0x2000,
 
    // Refer to 5-2 Status for details (see @OR_E5_STATUS_1 and @OR_E5_STATUS_2)
    OR_E5_SWR_STATUS = 0x2001,
 
    // Internal Set Point(see appendix *1) - SP lower limit to SP upper limit
    OR_E5_SWR_ISP = 0x2002,
 
    // Heater Current 1 Value Monitor, 0x00000000 to 0x00000226 (0.0 to 55.0)
    OR_E5_SWR_HeaterCurrentValue1_Monitor = 0x2003,
 
    // MV Monitor (Heating)
    //  Standard: 0xFFFFFFCE to 0x0000041A (−5.0 to 105.0)
    //  Heating and cooling: 0x00000000 to 0x0000041A (0.0 to 105.0)
    OR_E5_SWR_MVMonitorHeating = 0x2004,
 
    // MV Monitor (Cooling)
    //  0x00000000 to 0x0000041A (0.0 to 105.0)
    OR_E5_SWR_MVMonitorCooling = 0x2005,
 
    // Set Point -  SP lower limit to SP upper limit
    OR_E5_SWR_SP_LIMIT = 0x2103,
 
    // Alarm Value 1
    //   0xFFFFF831 to 0x0000270F (−1999 to 9999)
    OR_E5_SWR_ALARM_1 = 0x2104,
 
    // Alarm Value - Upper Limit 1
    //   0xFFFFF831 to 0x0000270F (−1999 to 9999)
    OR_E5_SWR_ALARM_1_UL = 0x2105,
 
    // Alarm Value - Lower Limit 1
    //   0xFFFFF831 to 0x0000270F (−1999 to 9999)
    OR_E5_SWR_ALARM_1_LL = 0x2106,
 
    // Alarm Value 2
    //   0xFFFFF831 to 0x0000270F (−1999 to 9999)
    OR_E5_SWR_ALARM_2 = 0x2107,
 
    // Alarm Value - Upper Limit 1
    //   0xFFFFF831 to 0x0000270F (−1999 to 9999)
    OR_E5_SWR_ALARM_2_UL = 0x2108,
 
    // Alarm Value - Lower Limit 1
    //   0xFFFFF831 to 0x0000270F (−1999 to 9999)
    OR_E5_SWR_ALARM_2_LL = 0x2109,
 
    //Temperature: Use the specified range for each sensor.
    // Analog: Scaling lower limit − 5% FS to Scaling upper limit + 5% FS
    OR_E5_SWR_PV2 = 0x2402,
 
    // Internal Set Point(see appendix *1) - SP lower limit to SP upper limit
    OR_E5_SWR_ISP2 = 0x2403,
 
    // Multi SP No. Monitor, 0x00000000 to 0x00000007 (0 to 7)
    OR_E5_SWR_MSMON = 0x2404,
 
    // Status,
    //  - Not displayed on the Controller display.
    //  - In 2-byte mode, the rightmost 16 bits are read.
    OR_E5_SWR_STATUSEX = 0x2406,
 
    // Status,
    //  - Not displayed on the Controller display.
    //  - In 2-byte mode, the leftmost 16 bits are read.
    OR_E5_SWR_STATUSEXL = 0x2407,
 
    // Status,
    //  - Not displayed on the Controller display.
    //  - In 2-byte mode, the rightmost 16 bits are read.
    OR_E5_SWR_STATUSEXR = 0x2408,
 
    // Decimal Point Monitor,
    // 0x00000000 to 0x00000003 (0 to 3)
    OR_E5_SWR_DECMON = 0x2410,
 
    // Set Point ()
    // SP lower limit to SP upper limit
    OR_E5_SWR_SP = 0x2601,
 
    // Remote Set Point Monitor
    // - Remote SP lower limit −10% FS to Remote SP upper limit +10% FS
    OR_E5_SWR_SP_EX_MON = 0x2602,
 
    // Heater Current 1 Value Monitor, 0x00000000 to 0x00000226 (0.0 to 55.0)
    OR_E5_SWR_HeaterCurrentValue1_Monitor2 = 0x2604,
 
    // Valve Opening Monitor, 0xFFFFFF9C to 0x0000044C (−10.0 to 110.0)
    OR_E5_SWR_VALVE_OPENING_MON = 0x2607,
 
    //  Proportional Band (Cooling), 0x00000001 to 0x0000270F (0.1 to 999.9)
    OR_E5_SWR_PRO_BAND = 0x2701,
 
    //  Integral Time (Cooling) 0x00000000 to 0x0000270F
    // (0 to 9999: Integral/derivative time unit is 1 s.)
    // (0.0 to 999.9: Integral/derivative time unit is 0.1 s.)
    OR_E5_SWR_IT_COOLING = 0x2702,
 
    //  Derivative Time (Cooling) 0x00000000 to 0x0000270F
    //  (0 to 9999: Integral/derivative time unit is 1 s.)
    //  (0.0 to 999.9: Integral/derivative time unit is 0.1 s.)
    OR_E5_SWR_D_COOLING = 0x2703,
 
    // Dead Band 0xFFFFF831 to 0x0000270F
    // (−199.9 to 999.9 for temperature input)
    // (−19.99 to 99.99 for analog input)
    OR_E5_SWR_DEADBAND = 0x2704,
 
    // Manual Reset Value,
    //  0x00000000 to 0x000003E8 (0.0 to 100.0)
    OR_E5_SWR_MANUAL_RESET_VALUE = 0x2705,
 
    // Hysteresis (Heating)
    // 0x00000001 to 0x0000270F
    // (0.1 to 999.9 for temperature input)
    // (0.01 to 99.99 for analog input)
    OR_E5_SWR_HYSTERESIS = 0x2706,
 
    // Hysteresis (Cooling)
    //  0x00000001 to 0x0000270F
    //  (0.1 to 999.9 for temperature input)
    //  (0.01 to 99.99 for analog input)
    OR_E5_SWR_HYSTERESIS_COOLING = 0x2707,
 
    // Control Period (Heating)
    //  0xFFFFFFFE (−2): 0.1 s
    //  0xFFFFFFFF (−1): 0.2 s
    //  0x00000000 (0): 0.5 s
    //  0x00000001 to 0x00000063 (1 to 99)
    OR_E5_SWR_CONTROL_PERIOD_HEATING = 0x2708,
 
    // Control Period (Cooling)
    //  0xFFFFFFFE (−2): 0.1 s
    //  0xFFFFFFFF (−1): 0.2 s
    //  0x00000000 (0): 0.5 s
    //  0x00000001 to 0x00000063 (1 to 99)
    OR_E5_SWR_CONTROL_PERIOD_COOLING = 0x2709,
 
    // Position Proportional Dead Band
    //  0x00000001 to 0x00000064 (0.1 to 10.0)
    OR_E5_SWR_POSITION_PROPORTIONAL_DEAD_BAND = 0x270A,
 
    // Open/Close Hysteresis
    //  0x00000001 to 0x000000C8 (0.1 to 20.0)
    OR_E5_SWR_OPEN_CLOSE_HYSTERESIS = 0x270B,
 
    // SP Ramp Time Unit 0x00000000 (0): EU/second
    //  0x00000001 (1): EU/minute
    //  0x00000002 (2): EU/hour
    OR_E5_SWR_SP_RAMP_UNIT = 0x270C,
 
    // SP Ramp Set Value 0x00000000 (0): OFF
    //  0x00000001 to 0x0000270F (1 to 9999)
    OR_E5_SWR_SP_RAMP_SET_VALUE = 0x270D,
 
    // SP Ramp Fall Value
    //  0xFFFFFFFF (−1): Same (Same as SP Ramp Set Value.)
    //  0x00000000 (0): OFF
    //  0x00000001 to 0x0000270F (1 to 9999)
    OR_E5_SWR_SP_FALL_VALUE = 0x270E,
 
    //  MV at Stop Standard Models
    //  Standard control:
    //      0xFFFFFFCE to 0x0000041A (−5.0 to 105.0)
    //  Heating and cooling control:
    //      0xFFFFFBE6 to 0x0000041A (−105.0 to 105.0)
    //  Position-proportional Models
    //      Close position-proportional control with the Direct Setting of
    //      Position Proportional MV parameter set to ON:
    //      0xFFFFFFCE to 0x0000041A (−5.0 to 105.0)
    //      Floating position-proportional control or the Direct Setting of
    //      Position Proportional MV parameter set to OFF:
    //      0xFFFFFFFF to 0x00000001 (−1 to 1)
    OR_E5_SWR_MV_PV_ERROR = 0x2711,
 
    // MV Change Rate Limit
    //  0x00000000 to 0x000003E8 (0.0 to 100.0)
    OR_E5_SWR_CHANGE_RATE_LIMIT = 0x2713,
 
    // PV Input Slope Coefficient
    //  0x00000001 to 0x0000270F (0.001 to 9.999)
    OR_E5_SWR_PV_INPUT_SLOPE_COEFFICIENT = 0x2718,
 
    // Heater Burnout Detection 1
    //  0x00000000 to 0x000001F4 (0.0 to 50.0)
    OR_E5_SWR_HEATER_BURNOUT_DETECTION_1 = 0x271B,
 
    // Leakage Current 1 Monitor
    //  0x00000000 to 0x00000226 (0.0 to 55.0)
    OR_E5_SWR_LEAKAGE_CURRENT_MONITOR_1 = 0x271C,
 
    // HS Alarm 1
    //  0x00000000 to 0x000001F4 (0.0 to 50.0)
    OR_E5_SWR_HS_ALARM_1 = 0x271D,
 
    // Process Value Input Shift
    //  0xFFFFF831 to 0x0000270F (−1999 to 9999)
    OR_E5_SWR_PROCESS_VALUE_INPUT_SHIFT = 0x2723,
 
    // Heater Burnout Detection 2
    //  0x00000000 to 0x000001F4 (0.0 to 50.0)
    OR_E5_SWR_HEATER_BURNOUT_DETECTION_2 = 0x2725,
 
    // Leakage Current 2 Monitor
    //  0x00000000 to 0x00000226 (0.0 to 55.0)
    OR_E5_SWR_LEAKAGE_CURRENT_MONITOR_2 = 0x2726,
 
    // HS Alarm 12
    //  0x00000000 to 0x000001F4 (0.0 to 50.0)
    OR_E5_SWR_HS_ALARM_2 = 0x2727,
 
    // Soak Time Remain (how lovely)
    //  0x00000000 to 0x0000270F (0 to 9999)
    OR_E5_SWR_SOAK_REMAIN = 0x2728,
 
    // Soak Time
    //  0x00000001 to 0x0000270F (1 to 9999)
    OR_E5_SWR_SOAK_TIME = 0x2729,
 
    // Wait Band 0x00000000 (0): OFF
    //  0x00000001 to 0x0000270F
    //  (0.1 to 999.9 for Temperature input)
    //  (0.01 to 99.99 for Analog input)
    OR_E5_SWR_WAIT_BAND = 0x272A,
 
    // Remote SP Input Shift
    //  0xFFFFF831 to 0x0000270F (−1999 to 9999)
    OR_E5_SWR_REMOTE_SP_SHIFT = 0x272B,
 
    // Remote SP input Slope Coefficient
    //  0x00000001 to 0x0
    OR_E5_SWR_REMOTE_SP_SLOPE_COEFFICIENT = 0x272C,
 
    //  Input Digital Filter 0x00000000 to 0x0000270F (0.0 to 999.9)
    OR_E5_SWR_DIGITAL_FILTER = 0x2800
 
    // Notes :
    // *1 Not displayed on the Controller display
};